28.5*28.5mm Eachine AE65 Crazybee X V2.2 1-2S Flight Controller 5A 4 In 1 ESC Betaflight OSD MPU-6000 for AE65 RC FPV Racing Drone

$52.99 $206.99
DESCRIPTION

Specification:

Brand: Eachine

Item Name: AE65 Crazybee X V2.2 Flight Controller


Flight Controller

MCU: STM32F411CEU6 (100MHZ, 512K FLASH)

Sensor: MPU-6000(SPI connection)
Board Size: 28.5 * 28.5mm
Power Supply: 1S-2S Battery Input (DC 2.9V-8.7V)
Built-in 5A(each) Blheli_S 4In1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI Frsky Receiver Support D8/D16
Built-in 5V 1A BEC
Built-in Voltage Detection
Firmware Target: CRAZYBEEF4FR

 Onboard 4 In 1 ESC

EFM8BB21

Power Supply: 1-2S LiPo/LiPo HV
Current: 5A Continuous, Peak 6A (3 seconds)
Support BLHeliSuite Programmable
Factory Firmware: S_H_50_REV16_7.HEX
Default Protocol: DSHOT600

 (CrazybeeX FR V1.0 version)

Onboard Frsky SPI receiver

SPI BUS Receiver Frsky D8/D16 Compatible

Support for Futaba S-FHSS (Need Betaflight 4.0.5 firmware or latest), Frsky_X_LBT(EU-LBT)

Channels: 8CH / 16CH
Failsafe Support
No ground interference ( Transmitter and receiver 1 m from the ground): 100m~200m

 (CrazybeeX FS V1.0 version)

Onboard Flysky SPI receiver

SPI BUS Receiver

Protocol: AFHDS and AFHDS-2A Switchable
Channels: 8CH(AFHDS) or 14CH(AFHDS-2A)
No ground interference ( Transmitter and receiver 1 m from the ground): 100~200m
Failsafe Support

 (CrazybeeX PNP V1.0 version)

 No onboard SPI receiver

 Onboard 5.8g VTX

Output Power: 25mw

Frequency: 40CH
Input Voltage: 3.3V 5.5V
Current Consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band
Smartaudio Ready
Default vtx_power should set to be “2”

 Onboard Voltage and Current detector

Voltage Meter Scale “110”
Amperage Mete Scale “1175”



Features:

CrazybeeX FR V2.2 Bind procedure:

1.  Make the on board receiver get into bind mode: For 3.5.7 version firmware Plug USB and then press the bind button for 1 second , the Red LED on the top of the flight controller will getting to be solid , this indicate the receiver is in bind mode; For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED on the top of the flight controller will getting to be solid , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”

2.  Make your Frsky transmitter get into bind mode . If bind is successful the red led will starting to blink.   The red LED wouldn’t blinking when binding with some new ACCESS firmware frsky radio  , but the bind is actual successful , need to go to CLI command and type “save” to finish the binding .

CrazybeeX FS V2.2 Bind procedure:

1.  Make the on board receiver get into bind mode: For 3.5.7 version firmware Press and hold the bind button for 1 second ,then plug USB, the Red LED at the bottom of the flight controller will blinking fast , this indicate the receiver is in bind mode; For 4.0.x version firmware Plug USB and then connect betaflight configurator and then move to CLI tab , type “bind_rx_spi” ,the Red LED at the bottom of the flight controller will blinking fast , the onboard receiver is in bind mode; For 4.1.x or 4.2.x the bind code is “bind_rx”

2.  Make your Flysky transmitter get into bind mode . If bind is successful the red led will getting to be solid.

 


Package Included:

1 X Eachine AE65 Crazybee X V2.2Flight Controller (Optional)



YOU MAY LIKE